123.hp.com/amp103

HP Amp 103 Printer Unboxing

To unbox your HP AMP 103 and remove the packaging materials, follow the steps given below:

• First, open the cardboard box. Now, you’ll find some setup posters.
• Keep them aside and remove the cardboard piece. It also contains pockets on the sides.
• You’ll find the ink cartridges and power cord in the pockets on the sides.
• Now, remove the cartridges and the power cord and keep them aside.
• Next, Tilt the cardboard box and lay it on some hard surface.
• Now, gently drag the HP AMP 103 printer out of the box using the strap of plastic attached to the front.
• Then, remove the Styrofoam caps on either sides.
• Make a small tear on the plastic film such that it causes no harm to the printer.
• Then, peel away the transparent film.

In a few more steps, you can download and install the software drivers from 123.hp.com/amp103 or 123.hp.com/setup 103 .

HP Amp 103 Installing Ink cartridges

Before you start installing the ink cartridges, the printer should be switched on.

• First, take the power cord that you kept aside earlier and insert one end of the power cord into the power slot located on the rear of the printer.
• Then, plug in the other end of the power cord directly into a wall outlet.
• Now, press the power button on your printer to switch it on.
• Wait for a few moments before you open the ink cartridge access area.
• Then, let the ink cartridge slots reach the center before you start inserting the ink cartridges into the slot.
• Next, remove the cartridge from the wrapper and peel away the orange pull tab on the copper colored contacts.
• Without touching the copper-colored contacts, insert the cartridge into the empty slot according to colour.
• Similarly, insert the other ink cartridge into the empty slot.

This is the first step in setting up your printer after downloading the software drivers from 123.hp.com/amp103 .

Learn how to connect your printer wirelessly and install software drivers from 123.hp.com/amp103

• First, press the wireless button on your HP AMP 103. The wireless light on the printer should stop blinking now. Once the light stops blinking, the printer will print out an alignment page.
• Next, complete the Wireless Setup by following the instructions on the page.
• Then, open a browser on your system and go to 123.hp.com/amp103 .
• Now, press the Download button on the webpage and wait for the driver download to complete.

• You’ll see a few instructions on the screen. Follow these instructions to proceed with the installation.
• Then, the printer will ask how you’d like to connect the printer to your system.
• Choose wireless and insert the USB cable into the respective slot when prompted.
• Next, allow printer access to your computer and by choosing the Wireless option.
• Then, enter your Wi-Fi password and wait for the wireless to stop blinking.
• Finally, disconnect the USB cable and follow the instructions to complete the installation.

Use the ePrint service to print your documents remotely. As long as you’ve a strong internet connection you can mail your documents to the printer’s e-mail address from anywhere with an active internet connection. The only software drivers you need are the ones you’ve to download from 123.hp.com/amp103 or 123.hp.com/setup 103 . Follow the steps below to setup the ePrint service.

• First, you must setup the Web services. To do that, press and hold down the power button for about 3 seconds.
• Then, press the wireless button and the printer information button at the same time.
• Now, the printer prints out an information sheet.

• Look for the printer’s IP address on the information sheet and type it in your browser address bar.
• The Printer Configuration page opens. Click Web Services, Setup and Continue.
• Accept the terms and conditions and wait for the printer to print out an information page.

• First, download the HP Scan app from Google Playstore on your android device.
• Then, select Scan and Camera.
• Click the button on the bottom to take a picture of your document.
• When you’ve adjusted the boundaries of your document, you can tap the Apply icon to make changes to the document.
• If you want to add more documents, then tap the Add icon.
• In case you want to change the brightness, contrast, etc. of your document, you can use the Edit option.
• Save the scanned file in the format that you’d like.

Disclaimer:

We are independent third party service providers who provide guidance and related tips on setting up your printer and downloading & installing software drivers from 123.hp.com/amp103 . Also, we provide simple fixes for your printer related issues and queries. We are not specifically tied-up with HP and its services in any way nor do we trade any of its products or services. We’ve intended the usage of all the images, logos and content on this website for informational purposes alone. For issues related to service and warranty, contact the manufacturer directly and thoroughly examine our privacy policy.